If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on March 31, 2007, 11:31 pm
Hi, Friends,
I have a Kenmore Dehumidifier (model 580.54501) that has been working
dutifully in my basement for several years. It suddenly stopped
working a couple of days ago. The problem was that the "bucket full"
LED was slowly flashing (once every 1 or 2 seconds), and the motor did
not run. The humidity display was showing "01". It was definitely not
the bucket, because it was empty, and was properly placed. I even
removed the bucket and pressed the water level control switch all the
way in, the bucket full LED was still flashing. If I unplug the power
cord, and plug it back in, the unit will come back to life for about
10 seconds. During this period, the fan is turning and the humidity
display indicates 45. Then the fan stops, the humidity display goes
back to 01, and the bucket full LED starts to flash again. Has anybody
had this kind of problems before? I wonder whether this is a water
level control switch problem or a control circuit problem. Is there
any test I can do?
Many thanks!
L.L.
|
 
| |
Posted by Paul Franklin on April 1, 2007, 12:05 am
On 31 Mar 2007 20:31:24 -0700, liul15110@yahoo.com wrote:
>Hi, Friends,
>I have a Kenmore Dehumidifier (model 580.54501) that has been working
>dutifully in my basement for several years. It suddenly stopped
>working a couple of days ago. The problem was that the "bucket full"
>LED was slowly flashing (once every 1 or 2 seconds), and the motor did
>not run. The humidity display was showing "01". It was definitely not
>the bucket, because it was empty, and was properly placed. I even
>removed the bucket and pressed the water level control switch all the
>way in, the bucket full LED was still flashing. If I unplug the power
>cord, and plug it back in, the unit will come back to life for about
>10 seconds. During this period, the fan is turning and the humidity
>display indicates 45. Then the fan stops, the humidity display goes
>back to 01, and the bucket full LED starts to flash again. Has anybody
>had this kind of problems before? I wonder whether this is a water
>level control switch problem or a control circuit problem. Is there
>any test I can do?
>Many thanks!
>L.L.
The fact that it runs a bit and then stops makes me think the LED
flashing and 01 display is an error code. Do you have the manual? If
not, you may be able to access from www.sears.com/parts.
HTH,
Paul
|
|
Posted by on April 1, 2007, 12:28 pm
wrote:
> On 31 Mar 2007 20:31:24 -0700, liul15...@yahoo.com wrote:
>
>
>
>
>
> >Hi, Friends,
> >I have a Kenmore Dehumidifier (model 580.54501) that has been working
> >dutifully in my basement for several years. It suddenly stopped
> >working a couple of days ago. The problem was that the "bucket full"
> >LED was slowly flashing (once every 1 or 2 seconds), and the motor did
> >not run. The humidity display was showing "01". It was definitely not
> >the bucket, because it was empty, and was properly placed. I even
> >removed the bucket and pressed the water level control switch all the
> >way in, the bucket full LED was still flashing. If I unplug the power
> >cord, and plug it back in, the unit will come back to life for about
> >10 seconds. During this period, the fan is turning and the humidity
> >display indicates 45. Then the fan stops, the humidity display goes
> >back to 01, and the bucket full LED starts to flash again. Has anybody
> >had this kind of problems before? I wonder whether this is a water
> >level control switch problem or a control circuit problem. Is there
> >any test I can do?
> >Many thanks!
> >L.L.
>
> The fact that it runs a bit and then stops makes me think the LED
> flashing and 01 display is an error code. Do you have the manual? If
> not, you may be able to access fromwww.sears.com/parts.
>
> HTH,
>
> Paul- Hide quoted text -
>
> - Show quoted text -
Hi, Paul,
I have the manual, and it doesn't say. The troubleshooting section is
only one page, and the problem I have is not listed.
Thanks!
L.L.
|
|
Posted by on April 1, 2007, 4:07 am
On 1 Apr, 04:31, liul15...@yahoo.com wrote:
> Hi, Friends,
> I have a Kenmore Dehumidifier (model 580.54501) that has been working
> dutifully in my basement for several years. It suddenly stopped
> working a couple of days ago. The problem was that the "bucket full"
> LED was slowly flashing (once every 1 or 2 seconds), and the motor did
> not run. The humidity display was showing "01". It was definitely not
> the bucket, because it was empty, and was properly placed. I even
> removed the bucket and pressed the water level control switch all the
> way in, the bucket full LED was still flashing. If I unplug the power
> cord, and plug it back in, the unit will come back to life for about
> 10 seconds. During this period, the fan is turning and the humidity
> display indicates 45. Then the fan stops, the humidity display goes
> back to 01, and the bucket full LED starts to flash again. Has anybody
> had this kind of problems before? I wonder whether this is a water
> level control switch problem or a control circuit problem. Is there
> any test I can do?
> Many thanks!
> L.L.
put a multimeter on the float switch and find out.
NT
|
|
Posted by Art on April 1, 2007, 8:47 pm
If yours is one of the late model ones built by LG within the last few
years, be grateful it lasted so long. Most lasted barely 1 year. I had
mine replaced or fixed 3 times and am throwing it away. Note that they
shortened the warranty from 1/5 years to 1/1 year (in other words the new
ones do not get a refrigeration system 5 year warranty any more). I am
trying a Whirlpool this time from Lowes for $219. Still have a 5 year
warranty on the refrig system.
> Hi, Friends,
> I have a Kenmore Dehumidifier (model 580.54501) that has been working
> dutifully in my basement for several years. It suddenly stopped
> working a couple of days ago. The problem was that the "bucket full"
> LED was slowly flashing (once every 1 or 2 seconds), and the motor did
> not run. The humidity display was showing "01". It was definitely not
> the bucket, because it was empty, and was properly placed. I even
> removed the bucket and pressed the water level control switch all the
> way in, the bucket full LED was still flashing. If I unplug the power
> cord, and plug it back in, the unit will come back to life for about
> 10 seconds. During this period, the fan is turning and the humidity
> display indicates 45. Then the fan stops, the humidity display goes
> back to 01, and the bucket full LED starts to flash again. Has anybody
> had this kind of problems before? I wonder whether this is a water
> level control switch problem or a control circuit problem. Is there
> any test I can do?
> Many thanks!
> L.L.
>
|
| Similar Threads | Posted | | Dehumidifier Problem | August 13, 2005, 3:43 am |
| dehumidifier problem | September 3, 2007, 10:16 am |
| when do I need to use a dehumidifier? | August 21, 2006, 7:03 pm |
| LG Dehumidifier | December 1, 2006, 11:33 am |
| LG Dehumidifier | December 1, 2006, 11:36 am |
| dehumidifier | July 10, 2007, 10:10 am |
| Dehumidifier | August 19, 2007, 10:22 pm |
| Dehumidifier. | October 22, 2007, 11:12 am |
| Best Location for Dehumidifier | August 28, 2005, 12:28 pm |
| Dehumidifier challenge | September 19, 2005, 12:53 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap